Table of Contents
How to Install the Rosemount Flow Transmitter 3051
The Rosemount Flow Transmitter 3051 is a versatile and reliable device used in various industries to measure flow rates of liquids and gases. Installing this transmitter correctly is crucial to ensure accurate and consistent readings. In this article, we will guide you through the process of installing the Rosemount Flow Transmitter 3051 by following the manual provided by the manufacturer.
Before you begin the installation process, it is important to familiarize yourself with the components of the Rosemount Flow Transmitter 3051. The transmitter consists of a sensor, a transmitter housing, and a display unit. Make sure you have all the necessary tools and equipment required for the installation, such as a power supply, mounting Hardware, and wiring materials.
To start the installation process, first, identify a suitable location for mounting the transmitter. The location should be easily accessible for maintenance and calibration purposes. Ensure that the mounting surface is flat and stable to prevent any vibrations that could affect the accuracy of the readings.
Next, mount the transmitter housing securely using the provided mounting hardware. Make sure the housing is level and aligned properly to avoid any issues with the sensor calibration. Once the housing is mounted, connect the sensor to the transmitter using the appropriate wiring connections as specified in the manual.
After connecting the sensor to the transmitter, power up the transmitter using the recommended power supply. Check the display unit to ensure that the transmitter is receiving power and functioning properly. If there are any error messages or issues with the display, refer to the troubleshooting section of the manual for guidance.
Once the transmitter is powered up and functioning correctly, it is time to calibrate the sensor for accurate flow rate measurements. Follow the calibration procedures outlined in the manual carefully to ensure precise and reliable readings. It is important to calibrate the sensor regularly to maintain accuracy over time.
| ROC-2315 RO controller instruction (220V) | |||
| Model | ROC-2315 | ||
| Single detection | Dry Contact input | Raw water no water protection | |
| (six channels) | Low-pressure protection | ||
| \\u3000 | High-pressure protection | ||
| \\u3000 | Pure water tank high\\u00a0level | ||
| \\u3000 | External control mode signal | ||
| \\u3000 | Running reset | ||
| Control port | Dry Contact output | Raw water pump | SPST-NO low capacity : AC220V/3A Max ;AC110V/5A Max |
| (five channels) | Inlet valve | \\u3000 | |
| \\u3000 | High pressure pump | \\u3000 | |
| \\u3000 | Flush valve | \\u3000 | |
| \\u3000 | Conductivity over-limit drainge valve | \\u3000 | |
| Measurement detection point | Product water conductivity and with Automatic Temperature compensation (0\\uff5e50\\uff09\\u2103 | ||
| Measurement range | Conductivity : 0.1~200\\u03bcS/cm/1~2000\\u03bcS/cm/10~999\\u03bcS/cm (with different conductivity sensor ) | ||
| Product water temp. : 0~50\\u2103 | |||
| Accuracy | 1.5 level | ||
| Power supply | AC220V (\\u00b110%)\\u00a0,\\u00a050/60Hz | ||
| Working Environment | Temperature:\\uff080\\uff5e50\\uff09\\u2103\\u00a0; | ||
| Relative Humidity :\\u226485%RH\\u00a0(no condensation ) | |||
| Dimension | 96\\u00d796\\u00d7130mm( height \\u00d7width\\u00d7depth) | ||
| Hole size | 91\\u00d791mm\\uff08height \\u00d7width\\uff09 | ||
| Installation | Panel mounted ,fast installtion | ||
| Certification | CE | ||
After calibrating the sensor, perform a test run to verify the accuracy of the flow rate measurements. Compare the readings from the transmitter with a known reference to ensure that the device is providing accurate results. If there are any discrepancies, recalibrate the sensor and retest until the readings are consistent.
In conclusion, installing the Rosemount Flow Transmitter 3051 requires careful attention to detail and following the instructions provided in the manual. By following the steps outlined in this article, you can ensure a successful installation and accurate flow rate measurements. Remember to regularly maintain and calibrate the transmitter to ensure optimal performance. If you encounter any issues during the installation process, refer to the troubleshooting section of the manual or contact the manufacturer for assistance.
